SFJ

Facebook  YouTube

Small Farmer's Journal
PO Box 1627
Sisters, Oregon 97759
800-876-2893
541-549-2064
agrarian@smallfarmersjournal.com
Mon - Thu, 8am - 4pm PDT

Small Farmer's Journal Spring 2016 Vol 40 No 2

The Small Farmer’s Journal Spring 2016 issue is out!

Oregon Plowing Match • Ventilating Poultry Houses • Water Buffalo • Ducks • Quarantine Humanity • Ox Teamsters • New Seed Drill • G Haw Tool • Food-Energy • Rebuilding Hay Loader • Fearless Manure Spreader • Horselogging • Auction Tips • Artisanal Maple Syrup • Calcium in Soils • Aboard the Planetary Spaceship • Yamhill Heritage Museum • You Can’t Farm with Horses and Send Men to the Moon! • Peerless Steam Tractor

Spotlight On: Equipment & Facilities

Plowing with the Single Horse

Plowing with the Single Horse

All other aspects being equal, the primary difference in plowing, comfortably, with a single horse is that the animal walks on unplowed ground immediately adjacent to the previous furrow, rather than in the furrow. This will cause the point of draft at the shoulder to be somewhat higher and will dictate hitching longer and/or higher than with the animal walking down 5 to 8 inches lower in the furrow.

John Deere Model A Tractor

from issue:

Your John Deere Tractor has a range of speeds. These various speeds not only give you the flexibility and adaptability you want, but also they enable you to balance the load and the speed for maximum economy. However, if you are handling a light load and want to travel at slow speed, it is far better to put your tractor into the gear which gives you the speed you want than to use a higher gear and throttle down.

McCormick-Deering All Steel Corn Sheller

McCormick-Deering All-Steel Corn Sheller

from issue:

To obtain the best results in shelling, the machine should be run so that the crank makes about forty-five (45) revolutions per minute or the pulley shaft one hundred and seventy-five (175) revolutions per minute. When driving with belt be sure that this speed is maintained, as any speed in excess of this will have a tendency to cause the shelled corn to pass out with the cobs. The ears should be fed into the sheller point first.

Fjordworks Plowing the Market Garden Part 2

Fjordworks: Plowing the Market Garden Part 2

Within the context of the market garden, the principal aim for utilizing the moldboard is to initiate the process of creating a friable zone for the root systems of direct-seeded or transplanted cash crops to establish themselves in, where they will have sufficient access to all the plant nutrients, air, and moisture they require to bear successful fruits. To this end, it is critical for good plant growth to render the soil into a fine-textured crumbly condition and to ensure there is no compaction within the root zone.

Hay Making with a Single Horse Part 2

Hay Making with a Single Horse Part 2

by:
from issue:

From reading the Small Farmers Journal, I knew that some people are equally happy with either model, but because McCormick Deering had gone to the trouble of developing the No. 9, it suggests they could see that there were improvements to be made on the No. 7. Even if the improvement was small, with a single horse any improvement was likely to increase my chance of success.

Blacksmith Forge Styles

Blacksmith Forge Styles

from issue:

Blacksmith Forge Styles circa 1920.

Eighteen Dollar Harrow

Eighteen Dollar Harrow

by:
from issue:

This is the story of a harrow on a budget. I saw plans on the Tillers International website for building an adjustable spike tooth harrow. I modified the plans somewhat to suit the materials I had available and built a functional farm tool for eighteen dollars. The manufactured equivalent would have cost at least $300.

Hay Making with a Single Horse Part 4

Hay Making with a Single Horse Part 4

by:
from issue:

Over the last few years of making hay, the mowing, turning and making tripods has settled into a fairly comfortable pattern, but the process of getting it all together for the winter is still developing. In the beginning I did what everyone else around here does and got it baled, but one year I decided to try one small stack. The success of this first stack encouraged me to do more, and now most of my hay is stacked loose.

Walsh No Buckle Harness

from issue:

When first you become familiar with North American working harness you might come to the erroneous conclusion that, except for minor style variations, all harnesses are much the same. While quality and material issues are accounting for substantive differences in the modern harness, there were also interesting and important variations back in the early twentieth century which many of us today either have forgotten or never knew about. Perhaps the most significant example is the Walsh No Buckle Harness.

SmP Seeder-Roller

Seeder-Roller – SmP Séi-Roll 1.0 for Horse Traction

Because it is a renewable and environmentally friendly energy source, horse traction is currently undergoing a renaissance in small scale agricultural holdings, winegrowing, market gardening and forestry. Within this context, implements for animal traction with mechanical drivetrain and direct draft are gaining importance. One of the goals of Schaff mat Päerd is to support this process by the development of new equipment and related studies and publications.

Illusive Herd of Threshasaurus Sighted

Illusive Herd of Threshasaurus Sighted

by:
from issue:

The Threshasaurus’s large size and curious nature may appear antagonistic, but they are mostly curious and largely non-threatening. Be careful when approaching, however, as they do have sharp teeth and many fast moving, exposed pulleys.

The Cutting Edge

The Cutting Edge

by:
from issue:

In the morning we awoke to a three quarters of a mile long swath of old growth mixed conifer and aspen trees, uprooted and strewn everywhere we looked. We hadn’t moved here to become loggers, but it looked like God had other plans! We had chosen to become caretakers of this beautiful place because of the peace and quiet, the clean air, the myriad of birds and wildlife! Thus, we were presented with a challenge: how to clean up this blowdown in a clean, sustainable way.

New Horse-drawn Side Delivery Rakes from Europe

New Horse-drawn Side Delivery Rakes from Europe

In Northern Italy the two agricultural machinery manufacturers MAINARDI A. s.r.l. and REPOSSI Macchine Agricole s.r.l. produce a vast range of haying equipment with pto and hydraulic drive, also hay rakes with mechanical drive by the rear wheels. The majority of the sold machines of this type are currently used with small tractors and motor cultivators. The technology of these rakes is based on implements which were developed in the 1940s, when animal traction still played an important role in Italy’s agriculture.

Permanent Corncribs

A short piece on the construction of corncribs.

The Use and Construction of Home Made Implements

The Use and Construction of Home Made Implements

by: ,
from issue:

It is now possible to purchase a make of machine to suit almost any condition if the money is available. There is no doubt that eventually they will be quite generally used. However, the dry farmers are at present hard pressed financially and in many instances the purchase of very much machinery is out of the question. For the man of small means or limited acreage, a homemade implement may be utilized at least temporarily.

Ask A Teamster Tongue Length

Ask A Teamster: Tongue Length

My forecart pole is set up for draft horses. My husband thinks we should cut the pole off to permanently make it fit better to these smaller horses. What would be your opinion? Like your husband, my preference would be a shorter tongue for a small team like your Fjords. The dynamics and efficiency of draft are better if we have our horse(s) close to the load. A shorter tongue will also reduce the overall length of your outfit, thereby giving you better maneuverability and turning dynamics.

Choosing a Gas or Coal Forge for the Small Farm Shop

Choosing a Gas or Coal Forge for the Small Farm Shop

by:
from issue:

After you’ve built a small farm blacksmith shop, one of the first decisions that you’ll need to make is which type of fuel you’ll be using. Most people choose either gas (propane) or coal, however, wood fired forges are also an option. All three fuel types have pros and cons. The final decision will likely be based on the type of forging that you plan to do and the local availability of the fuel.

John Deere Side Delivery Rake No 594

John Deere Side Delivery Rake No. 594

from issue:

When starting a new side rake, turn the reel by hand to be sure it revolves freely and the teeth do not strike the stripper bars. Then throw the rake in gear and turn the wheel by hand to see that the tooth bars and gears run free. Breakage of parts, which causes serious delay and additional expense, can be avoided by taking these precautions before entering the field.

Small Farmer's Journal

Small Farmer's Journal
PO Box 1627
Sisters, Oregon 97759
800-876-2893
541-549-2064
agrarian@smallfarmersjournal.com
Mon - Thu, 8am - 4pm PDT